無心研磨機操作說明

研磨者 发表于 2008-2-20 09:19:21

無心研磨機操作說明<p class=\"MsoNormal\" style=\"text-justify:inter-ideograph;margin:0cm 0cm 0pt 12pt;text-indent:-12pt;line-height:10pt;text-align:justify;mso-line-height-rule:exactly;tab-stops:list 12.0pt;mso-list:l0 level1 lfo1\">1. 檢查機臺各部位是否正常,各油路、水油是否完好;<p class=\"MsoNormal\" style=\"text-justify:inter-ideograph;margin:0cm 0cm 0pt 12pt;text-indent:-12pt;line-height:10pt;text-align:justify;mso-line-height-rule:exactly;tab-stops:list 12.0pt;mso-list:l0 level1 lfo1\">2. 根據工件所需加工的Φ徑,選擇合適的刀,並將刀板 (6)放在刀座(38)上,檢查刀的中心高度32.5mm是否夠,如不夠需墊墊片;<p class=\"MsoNormal\" style=\"text-justify:inter-ideograph;margin:0cm 0cm 0pt 12pt;text-indent:-12pt;line-height:10pt;text-align:justify;mso-line-height-rule:exactly;tab-stops:list 12.0pt;mso-list:l0 level1 lfo1\">3. 用螺釘將刀板(8)固定於刀座(38)上;<p class=\"MsoNormal\" style=\"text-justify:inter-ideograph;margin:0cm 0cm 0pt 12pt;text-indent:-12pt;line-height:10pt;text-align:justify;mso-line-height-rule:exactly;tab-stops:list 12.0pt;mso-list:l0 level1 lfo1\">4. 用工作臺進刀手輪(18)將工作臺(23)向后退;<p class=\"MsoNormal\" style=\"text-justify:inter-ideograph;margin:0cm 0cm 0pt 12pt;text-indent:-12pt;line-height:10pt;text-align:justify;mso-line-height-rule:exactly;tab-stops:list 12.0pt;mso-list:l0 level1 lfo1\">5. 用調整輪進刀手輪(15)將調整輪(21)向后退,使砂輪(22)與調整輪(21)之間的間隙足夠大,能放得下工件;<p class=\"MsoNormal\" style=\"text-justify:inter-ideograph;margin:0cm 0cm 0pt 12pt;text-indent:-12pt;line-height:10pt;text-align:justify;mso-line-height-rule:exactly;tab-stops:list 12.0pt;mso-list:l0 level1 lfo1\">6. 把工件放在刀板(6)上,將砂輪(22)和調整輪(21)調到與刀板(6)適當的位置,且工件與砂輪(22)和調整輪(21)有輕微的摩擦;<p class=\"MsoNormal\" style=\"text-justify:inter-ideograph;margin:0cm 0cm 0pt 12pt;text-indent:-12pt;line-height:10pt;text-align:justify;mso-line-height-rule:exactly;tab-stops:list 12.0pt;mso-list:l0 level1 lfo1\">7. 用螺釘把調整輪進刀手輪鎖緊,用螺絲將工作臺進刀手輪(19)鎖緊;<p class=\"MsoNormal\" style=\"text-justify:inter-ideograph;margin:0cm 0cm 0pt 12pt;text-indent:-12pt;line-height:10pt;text-align:justify;mso-line-height-rule:exactly;tab-stops:list 12.0pt;mso-list:l0 level1 lfo1\">8. 拿出工件,抬起扳手(39),使調整輪(21)后退,其與砂輪(22)之間的間隙變大,有利於放工件;<p class=\"MsoNormal\" style=\"text-justify:inter-ideograph;margin:0cm 0cm 0pt 12pt;text-indent:-12pt;line-height:10pt;text-align:justify;mso-line-height-rule:exactly;tab-stops:list 12.0pt;mso-list:l0 level1 lfo1\">9. 打開機臺電源開關(34),打開砂輪開關(36),打開調整輪開關(35);<p class=\"MsoNormal\" style=\"text-justify:inter-ideograph;margin:0cm 0cm 0pt 12pt;text-indent:-12pt;line-height:10pt;text-align:justify;mso-line-height-rule:exactly;tab-stops:list 12.0pt;mso-list:l0 level1 lfo1\">10. 將工件帖在調整輪(21)一邊,輕輕放於刀板(6)上,用手壓扳手(39),慢慢下刀;<p class=\"MsoNormal\" style=\"text-justify:inter-ideograph;margin:0cm 0cm 0pt 12pt;text-indent:-12pt;line-height:10pt;text-align:justify;mso-line-height-rule:exactly;tab-stops:list 12.0pt;mso-list:l0 level1 lfo1\">11. 如果工件加工后有錐度,用調整水平斜度螺絲(16)慢慢將度數調為0度;<p class=\"MsoNormal\" style=\"text-justify:inter-ideograph;margin:0cm 0cm 0pt 12pt;text-indent:-12pt;line-height:10pt;text-align:justify;mso-line-height-rule:exactly;tab-stops:list 12.0pt;mso-list:l0 level1 lfo1\">12. 工件加工后,如沒達到所需Φ徑,可用工作臺微調進刀手輪(19)進刀;<p class=\"MsoNormal\" style=\"text-justify:inter-ideograph;margin:0cm 0cm 0pt 12pt;text-indent:-12pt;line-height:10pt;text-align:justify;mso-line-height-rule:exactly;tab-stops:list 12.0pt;mso-list:l0 level1 lfo1\">13. 如果加工工件的余量多,需打開冷卻液開關(32),放冷卻液;<p class=\"MsoNormal\" style=\"text-justify:inter-ideograph;margin:0cm 0cm 0pt 12pt;text-indent:-12pt;line-height:10pt;text-align:justify;mso-line-height-rule:exactly;tab-stops:list 12.0pt;mso-list:l0 level1 lfo1\">14. 工件加工完后,需做好機臺的衛生及保養.

boywhz 发表于 2009-5-28 08:55:35

没图啊，看不太明白

页: [1]

磨削技术网's Archiver

無心研磨機操作說明