加工中心标准训练样件一(NC代码)

nazszgaf32

- Q& w  g9 Z! H手工编程（适用于FANUC）
" J, l! }6 r1 F* N8 V主程序
# v; h' m" {( R$ V% t%
o1
G91G28Z0.
T1M6
G90G54G0X0Y0S500M3
G43H1Z100.
  Z- v: a; G9 S* T7 {5 r0 P8 p' [X-65.Y0
Z5.0
% G' X, Y, ^$ @2 C, n( M( MG01Z-8.F50
7 F! a+ m+ r4 G# WM98P100D1(D=8.2)
* l2 q: P  I7 D8 n& A3 {9 G, k$ UG01Z-16.F50
M98P100D1(D=8.2)
( P4 K" C: t, sG01Z-24.F50
1 B2 u( O) A7 CM98P100D1(D=8.2)
0 x4 t4 n$ H- @4 v3 h( y4 aG0Z100.
9 Y( Z0 ]! w& k2 T5 a& I, [M05
G91G28Z0
8 v: J; n# d- r( |$ F/ v+ cT2M6
G90G54G0X0Y0S1000M3
3 |+ C3 D$ N8 j, g% j/ NG43H2Z100.
) J# }2 Q8 {& O, X& QX-65.Y0
Z5.0
G01Z-5.F50
6 k, x5 L7 n  D4 @: U0 a! oM98P100D2(D=5.)
& a! Y: g+ v/ K6 u- Y0 yG01Z-10.F50
" n! z, U3 m7 w' K* CM98P100D2(D=5.)
# Y7 n+ F& J+ F2 O8 D3 FG01Z-15.F50
M98P100D2(D=5.)
7 D* x- H/ l1 k) q  K: J* ]G01Z-20.F50
M98P100D2(D=5.)
6 ?. }% \' n4 L$ C: IG01Z-24.F50
M98P100D2(D=5.)
, g9 M4 r9 s4 {$ D1 WG0Z100.
M05
G91G28Z0
2 k( l" X6 |$ i- h: q! HT3M6
3 g+ s5 ]# L4 x% j) RG90G54G0X0Y0S1500M03
G43H3Z100.0
* M- b2 E/ W4 Q5 w7 }9 T  a; U9 wG98G81R5.0Z-5.0F80
( w) ~9 Q" R% X- KG80
M05
8 u% [+ c% P" }6 c! oG91G28Z0
T4M06
G90G54G0X0Y0S1500M03
G43H4Z100.0M08
G98G83R5.0Z-42.0Q2.0F70
% ]$ U5 L  x4 y; }7 @1 U7 Z$ n: nG80
; v4 X! V$ V) z# \, |7 i2 U# kM05
G91G28Z0
" J" }) F* E9 p1 k- g7 [3 T! mT5M06
- Q; l( j6 Q, p- Q! N  {G90G54G0X0Y0S180M03
G43H5Z100.0M08
) J5 A, t" y- p8 _. O8 wG98G81R5.0Z-45.0F40
G80
7 C& Y% `8 U6 R8 y! t% {3 |9 D3 u( K+ ~M05
M09
" s: J/ m$ F  N8 @* GG91G28Z0
0 U+ b! G  R( OM30
# O8 o9 j  v9 a( _! p& C! _" Y  o%
9 w8 H2 E/ e$ z- F, v5 ]& K& W子程序O100
) V8 [; ]1 v9 H: D4 a%
3 @$ y" D2 ]9 gG41G01X-65.Y-30.0F100
. s/ d2 l" G' @5 V$ SG03X-35.Y0R30.
3 B: H5 }  U4 P' u! b# @G01Y32.
G02X-32.Y35.R3.
1 ?% u4 P0 P1 }, C5 n7 t' Q2 |" zG01X32.
G02X35.Y32.R3.
G01Y-32.
G02X32.Y-35.R3.
( G, v& b; C$ e- U0 rG01X-32.
7 D; P; v9 K. j% k, O$ DG02X-35.Y-32.R3.
G01Y0
* c7 I8 q/ @2 I& r1 x* UG03X-65.0Y30.R30.
3 _; b- W; ]5 ~! @% u2 J2 ?+ ^G40G01Y0
M99
+ N) L9 \# v% [7 s%
4 B4 a) Y- ~# W9 O文章关键词：