找回密码
 注册会员

QQ登录

只需一步,快速开始

扫一扫,访问微社区

查看: 230|回复: 0

[出售] 装配平台HT200-300

[复制链接]
发表于 2016-4-23 11:05:44 | 显示全部楼层 |阅读模式

马上注册,结交更多好友,享用更多功能,让你轻松玩转磨削论坛

您需要 登录 才可以下载或查看,没有账号?注册会员

×

5 N( D+ q9 ^/ j( ]装配平台用途:应用于动力机械设备的装配及调试,表面带有T形槽,装配平台可以固定动力机械设备。工作面上可加工圆孔、U型孔或长孔。材质:优质高强度灰口铸铁HT200-250,工作面硬度为HB170-240,铸件经过两次人工退火600℃-700℃或自然时效2-3年,完全去除内应力,精度稳定,耐磨性能好。
, ]4 P4 N$ F: g装配平台包装:木制包装。包装前经防锈处理并妥善包装,避免因包装不善而在运输过程中损坏产品。平板经检定合格后,应附有产品合格证;产品合格证上应出厂日期和产品序号。
3 Z8 y" i6 p. Q' q0 i$ a装配平台是划线、测量、铆焊、工装工艺不可以缺少的工作台,也可以做机械试验平台等等。在装配平台的生产设计上采用箱体式、筋板式或其他结构型式。在装配平台的相对两侧面上,应有安装手柄或吊装位置的设置、螺纹孔或圆柱孔。0 m  L- }8 b* U! r; l
装配平台技术要求  1、平板工作面不得有严重影响外观和使用性能的砂孔、气孔、裂纹、夹渣、缩松、划痕、碰伤、锈点等缺陷。3 b0 \0 [) F' h7 T- d
2、平板的铸造表面应清除型砂且平整,涂漆牢固。
8 \7 K  u5 L! W# R1 ]) `3、平板应采用优质细密的灰口铸铁或合金等材料制造,其工作面硬度应为170-220HB。
' l+ Y" I- V8 J9 `' M4、平板工作面通常应采用刮削工艺。( D# \) n% ~# i! J; y+ z  c
5、平面度公差见表2的规定。' n% [1 \  I; C9 i! }8 ~
Assembly plate are usually used to fit and debug the equipment.there are T-slot on the surface plate to fit the workpiece. Additionally, we can machine the round hole U-shaped, slot holes or other your desire on the surface plate.
5 R$ D9 f  k% b' ^! T9 u3 ^) jThe raw material of the cast iron assembly plate is the high -strength cast iron HT200-300 ,whose surface hardness is of HB170-240.After the two manual handing such as 600℃ to 700℃ artificial annealing as well as 2 to 3 years of natural aging, the T-slot has plate perfectly resists abrasion and has stable precision.
2 \7 C' ^  L' w1 p9 V' \Technical requirements of assembly Plate:& Z. O& l" S3 N7 h, c9 p" B
1.The working surface, when inspected visually, shall be free from blowholes, sand holes, cracks, slag inclusions scratches, porous patches and other visual flaws.
4 z1 I& Q! B- u2.The working surface shall be clean and uniform and the other sides shall be painted well.6 H- v9 {; o/ l3 w3 Y1 S
3,The raw material of Cast Iron Surface Plate shall be the close-grained cast iron whose hardness is of HB 170~220.
1 h7 }& j0 W& m; I2 O# y; c4, the surface plate are usually adopted the scraping technology.8 G% N& H. P% c. o  }0 ~5 Z" Z% M; z
5,deviation from flatness of the working surface  shall not exceed the permitted deviations specified in Table2.
, O; u" }2 p  D! ]* d
- C% ~, Y3 I4 o' B7 ]5 i/ N) n
您需要登录后才可以回帖 登录 | 注册会员

本版积分规则

中国磨床技术论坛
论 坛 声 明 郑重声明:本论坛属技术交流,非盈利性论坛。本论坛言论纯属发表者个人意见,与“中国磨削技术论坛”立场无关。 涉及政治言论一律删除,请所有会员注意.论坛资源由会员从网上收集整理所得,版权属于原作者. 论坛所有资源是进行学习和科研测试之用,请在下载后24小时删除, 本站出于学习和科研的目的进行交流和讨论,如有侵犯原作者的版权, 请来信告知,我们将立即做出整改,并给予相应的答复,谢谢合作!

中国磨削网

QQ|Archiver|手机版|小黑屋|磨削技术网 ( 苏ICP备12056899号-1 )

GMT+8, 2025-4-26 12:54 , Processed in 0.143774 second(s), 23 queries .

Powered by Discuz! X3.5

© 2001-2024 Discuz! Team.

快速回复 返回顶部 返回列表