螺纹类零件7的数控车床加工编程源程序

huangwenyu33

螺纹类零件7的数控车床加工编程源程序：
, t+ I  ^' K* ^- M, oN10 G92X100Z100
9 j8 y, m$ E$ w) d, ON20 M06T0101
N25 G04P3
N30 M03M07
N40 G90G00X42Z2
8 Z1 A' E7 l" e) x! o& FN50 G01Z0F200
N60 X15
) B/ \2 e, {* W" YN70 G90G00X60Z4
- W+ c7 d* I$ L7 {( H( G# U" SN80 G71U2W0R1P90Q140X0.5Z0F200
N90 G01X32Z4F100
N100 Z0
( ]- ?' {0 i2 YN110 X36Z-2
N120 Z-36
N130 X38
N140 Z-47
N145 G90G00X100
# y1 d' Y; x6 H9 z- F$ S% Y9 IN150 Z100
# l0 M- Y# s- S4 {$ j' ]3 m( O3 hN155 T0100
( M% ^3 }: r! J$ [# i1 Q, bN160 M05M00
N165 M06T0303
1 W6 H2 N4 m: I& g: M( G4 b3 yN170 G04P3
N180 M03
) ~. O: U% p1 P* `$ f# {+ NN190 G90G00X15Z2
N200 G71U1W0R1P210Q270X-0.5Z0F200
/ p9 \& B' n# X( U& sN210 G01X28Z2F100
N220 Z0
  j8 |5 `& k4 f% TN230 X26Z-1
" i3 E% L: q8 H6 r& @  fN240 Z-15
, m2 W, d) J3 IN250 G03X21Z-20R5
N260 G02X18Z-25R5
7 W, k! n+ h  ?- [/ W' YN270 G01Z-47
- d7 W3 O; \; t* ]# l( ?N280 T0300
# g: `7 v2 M  W3 I3 E& ?N290 M05
N300 M00
  L; o% l5 C) VN310 M06T0404
N320 G04P3
6 a( R, b; [* R* \, Q7 hN330 M03
7 w$ P* j9 x8 @3 w; |7 O- aN340 G90G00Z-36
N350 X42
4 v6 h) [7 Q# c  X: e( `/ t  x& SN360 G01X31F20
N370 G04P0.5
9 @+ A/ a# S% A$ j6 ^% VN380 G01X42F100
0 `; u0 r% d- k% U! n- y5 j  v% p, \N390 Z-32
  _8 R' `2 N; p& MN400 X31F20
N410 G04P0.5
N420 G01X100F100
8 W/ \, A4 B4 z2 `N430 Z100
N440 T0400
N450 M05M00
8 @  I# v4 O/ Z7 x* l" U1 iN460 M06T0202
- a% F7 z* ]# T6 o1 p5 d9 E, iN465 G04P3
N470 M03
$ D4 i5 ~$ S5 v- N- D8 G' S, ^N480 G90G00X40Z6
N490 G82X35.2Z-32F1.5
N500 G82X34.6Z-32F1.5
N510 G82X34.3Z-32F1.5
1 X( k0 }8 p4 w6 b" [" ]N520 G82X34.1Z-32F1.5
N530 G82X34.05Z-32F1.5
N540 G90G00X40
3 m; G, `( h% l0 vN550 Z4.5
9 ^0 s$ P6 q0 x( {N560 G82X35.2Z-32F1.5
N570 G82X34.6Z-32F1.5
. o/ g, U* H' C( F9 |# ON580 G82X34.3Z-32F1.5
* b; {2 m4 g+ E8 aN590 G82X34.1Z-32F1.5
N600 G82X34.05Z-32F1.5
N610 G90G00X100
6 A5 p7 G" f/ d; s4 m6 K+ _N620 Z100
/ O; m/ Y" W$ T) S/ E! AN630 T0200
+ f+ D. m: u7 K0 |5 u+ NN640 M05
7 ?; x' }4 i; y( r) kN650 M00
N660 M06T0404
- Z8 _/ x) S# M6 FN670 G04P3
9 |7 |+ X* Y9 O1 MN680 M03
  C9 O! l) @% X+ U& H' UN700 G90G00X42Z-48.975（假定切刀宽4mm）
4 ?6 g' Y% h# B, t9 _N710 G01X15F50
N720 G90G00X100Z100
6 D) p8 z  k1 @0 m+ IN730 T0400
N740 M05M09
N750 M30
( `/ |& G& W( B7 P0 [7 R文章关键词： 螺纹类零件7的数控车床加工编程源程序